[AKD5358B-B] 2010/01 - 1 - general description AKD5358B-B is an evaluation board for the digital audio 24bit 96k hz a/d converter, ak5358b. AKD5358B-B has analog input circuits and a digital interface transmitte r,and can achieve the interface with digital audio systems via opt-connector. ? ordering guide AKD5358B-B --- ak5358b evaluation board function ? dit (ak4114) with optical output lin v a +15v -> +5v reg reg vd dgnd agnd rin ak4114 (dit) opt out mclk sclk lrck sdto dsp data vcc va 10pin header ak5358b figure 1. AKD5358B-B block diagram * circuit diagram and pcb layout are attached at the end of this manual. AKD5358B-B ak5358b evaluation board rev.0
[AKD5358B-B] 2010/01 - 2 - 1. evaluation board manual ? operation sequence 1) set up the power supply lines. jack names jack colors voltage ranges used for comments and attentions default va ( note 1 ) red +7v +15v reguratort1: va of ak5358b should be always connected. +15v vd orange +2.7v +5.5v vd of ak5358b, 74hc14 should be always connected. +5v vcc green +3.0v +3.6v ak4114 should be always connected. +3.3v agnd black 0v analog ground should be always connected. gnd dgnd black 0v digital ground should be always connected. gnd table 1. set up the power supply lines. note 1. in case of using +5v power supply to connect vd, it is possible to supply the voltage to vd of ak5358b without using regulator(t1). in this case, jp3 is set to vd side. each supply line should be distributed from the power supply unit. 2) set up the evaluation mode, jumper pins and dip switches. (see the followings.) 3) power on. the ak5358b and ak4114 should be reset once bringing sw2 = ?l? upon power-up. ? evaluation mode (1) slave mode (1-1) a/d evaluation using dit function of ak4114 port2 (dit) is used. dit generate s audio bi-phase signal from receive d data and which is output through optical connector (totx141). it is possible to connect akm?s d/a converter evaluation boards on the digital-amplifier, which equips dir input. nothing should be connected to port1 (dsp). jp5 mclk figure 2. jumper setting, when using dit function of ak4114 (1-2) all interface signals including master clock are fed externally. port1 (dsp) is used. all interface signals (mclk, sclk, lrck) are provided to the ak5358b through port1. jp5 (mclk) should be open. the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk figure 3. jumper setting, when using port1(dsp)
[AKD5358B-B] 2010/01 - 3 - (2) master mode (2-1) a/d evaluation using dit function of ak4114 port2 (dit) is used. dit generate s audio bi-phase signal from receive d data and which is output through optical connector (totx141). it is possible to connect akm?s d/a converter evaluation boards on the digital-amplifier, which equips dir input. nothing should be connected to port1 (dsp). the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk figure 4. jumper setting, when using dit function of ak4114 (2-2) master clock is fed externally. port1 (dsp) is used. mclk is provided to the ak5358b through port1. jp5 (mclk) should be open. the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk figure 5. jumper setting, when using port1(dsp) ? other jumper pins set up 1. jp1 (gnd) : analog ground and digital ground open : separated. short : common. (the connector ?dgnd? can be open.) 2. jp2 (cks1) : setting of cks1 pin for ak5358b h : master mode l : slave mode 3. jp3 (va) : select va for ak5358b va : 5v supply from va connector reg : 5v supply from regulator. va connector should be supplied + 7 15v. 4. jp4 (vd) : select vd for ak5358b select vd
[AKD5358B-B] 2010/01 - 4 - ? dip switch set up [sw1] (mode1): setting the evaluation mode for ak5358b and ak4114 on is ?h?, off is ?l?. cks1 should be set by jp2. no. name off (?l?) on (?h?) 1 cks0 2 cks2 see table 2 ( note 2 ) 3 dif msb justified i 2 s compatible 4 dif1 ak4114 master mode ak4114 slave mode table 2. mode setting mode cks2 cks1 cks0 input level master/slave mclk sclk 0 l l l cmos slave 256/384fs (8khz fs 96khz) 512/768fs (8khz fs 48khz) 48fs or 32fs 1 l l h reserved 2 l h l cmos master 256fs (8khz fs 96khz) 64fs 3 l h h cmos master 512fs (8khz fs 48khz) 64fs 4 h l l ttl slave 256/384fs (~ 96khz) 512/768fs (~ 48khz) 48fs or 32fs 5 h l h reserved 6 h h l cmos master 384fs (8khz fs 96khz) 64fs 7 h h h cmos master 768fs (8khz fs 48khz) 64fs table 3. mode setting of ak5358b note 2: ak4114 does not support mclk=384fs/512fs/768fs. port1 (dsp) should be used when mclk=384fs/512fs/768fs. ? the function of the toggle sw upper-side is ?h? and lower-side is ?l?. [sw2] (pdn): resets the ak5358b and ak4114. keep ?h? during normal operation.
[AKD5358B-B] 2010/01 - 5 - ? analog input circuits analog signal is input via j1(rin) and j2(lin) of rca connectors. ainr j1 rin + c2 10u j2 lin ainl + c1 10u figure 6. analog input circuits * akm assumes no responsibility for the trouble when using the circuit examples.
[AKD5358B-B] 2010/01 - 6 - measurement results [measurement condition] ? measurement unit : audio precision, system two cascade ? mclk : 256fs ? sclk : 64fs ? fs : 48khz, 96khz ? bit : 24bit ? power supply : va = 5.0v, vd = 5.0v ? interface : dit ? temperature : room fs=48khz results parameter input signal measurement filter l ch r ch s/(n+d) 1khz, -1db 20klpf 93.1 db 93.0 db 20klpf 99.6 db 99.8 db dr 1khz, -60db 20klpf, a-weighted 102.1 db 102.6 db 20klpf 100.0 db 99.9 db s/n no input 20klpf, a-weighted 103.0 db 102.8 db fs=96khz results parameter input signal measurement filter l ch r ch s/(n+d) 1khz, -1db 40klpf 95.1 db 94.9 db 40klpf 99.4 db 99.4 db dr 1khz, -60db 40klpf, a-weighted 104.6 db 104.7 db 40klpf 99.5 db 99.4 db s/n no input 40klpf, a-weighted 105.0 db 104.8 db
[AKD5358B-B] 2010/01 - 7 - < |